T2080RDB-PC uboot 引导 Linux 内核启动_bar 6 failed to assign mem size-程序员宅基地

技术标签: linux  T2080RDB  uboot  nor flash  开发最前沿  

T2080RDB-PC uboot 引导Linux 内核启动

[email protected]

技术交流QQ群: 691976956

 

U-Boot 2016.012.0+ga9b437f (May 15 2016- 01:38:26 +0800)

CPU0:  T2080E, Version: 1.1,(0x85380011)

Core:  e6500, Version: 2.0,(0x80400120)

Clock Configuration:

      CPU0:1799.820 MHz, CPU1:1799.820 MHz, CPU2:1799.820 MHz, CPU3:1799.820 MHz,

      CCB:599.940 MHz,

      DDR:933.310 MHz (1866.620 MT/s data rate) (Asynchronous), IFC:149.985 MHz

      FMAN1: 699.930 MHz

      QMAN:  299.970 MHz

      PME:   599.940 MHz

L1:   D-cache 32 KiB enabled

      I-cache 32 KiB enabled

Reset Configuration Word (RCW):

      00000000: 1207001b 15000000 00000000 00000000

      00000010: 66150002 00000000 ec027000 c1000000

      00000020: 00800000 00000000 00000000 000307fc

      00000030: 00000000 00000000 00000000 00000004

I2C:  ready

Board: T2080RDB, Board rev: 0x01 CPLDver: 0x06, boot from NOR vBank0

SERDES Reference Clocks:

SD1_CLK1=156.25MHZ, SD1_CLK2=100.00MHZ

SD2_CLK1=100.00MHZ, SD2_CLK2=100.00MHZ

SPI:    ready

DRAM:   Initializing....using SPD

Detected UDIMM D3XP56082XL10AA 2GiB left unmapped

4 GiB (DDR3, 64-bit, CL=13, ECC on)

DDRChip-Select Interleaving Mode: CS0+CS1

VID: Could not find voltage regulator onI2C.

Warning: Adjusting core voltage failed.

Flash:   128 MiB

L2:      2 MiB enabled

Corenet Platform Cache: 512 KiB enabled

Using SERDES1 Protocol: 102 (0x66)

Using SERDES2 Protocol: 21 (0x15)

SEC0: RNG instantiated

NAND:    512 MiB

MMC:     FSL_SDHC: 0

EEPROM:  Invalid ID (ff ff ff ff)

PCIe1:   Endpoint, undetermined, regs @ 0xfe240000

PCIe1:   Bus 00 - 00

PCIe2:   Root Complex, x2 gen2, regs @ 0xfe250000

  02:00.0     -1957:0808 - Processor

PCIe2:   Bus 01 - 02

PCIe3:   disabled

PCIe4:   Root Complex, no link, regs @ 0xfe270000

PCIe4:   Bus 03 - 03

In:      serial

Out:     serial

Err:     serial

Net:     Fman1: Uploading microcodeversion 106.4.18

FM1@DTSEC3 [PRIME], FM1@DTSEC4,FM1@TGEC1, FM1@TGEC2, FM1@TGEC3, FM1@TGEC4

Hit any key to stop autoboot:  0

WARNING: adjusting available memory to30000000

## Booting kernel from Legacy Image ate8020000 ...

   Image Name:   Linux-4.1.8-rt8+gbd51baf

   Image Type:   PowerPCLinux Kernel Image (gzip compressed)

   Data Size:    5099857 Bytes = 4.9 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Loading init Ramdisk from LegacyImage at e9300000 ...

   Image Name:   fsl-image-mfgtool-t2080rdb-20160

   Image Type:   PowerPCLinux RAMDisk Image (gzip compressed)

   Data Size:    8398591Bytes = 8 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Flattened Device Tree blob ate8800000

   Booting using the fdt blobat 0xe8800000

   Uncompressing Kernel Image... OK

   Loading Ramdisk to2f7fd000, end 2ffff6ff ... OK

   Loading Device Tree to03fe3000, end 03fff2c0 ... OK

Reserved memory: initialized nodebman-fbpr, compatible id fsl,bman-fbpr

Reserved memory: initialized nodeqman-fqd, compatible id fsl,qman-fqd

Reserved memory: initialized nodeqman-pfdr, compatible id fsl,qman-pfdr

Reserved memory: initialized nodepme-pdsr, compatible id fsl,pme-pdsr

Reserved memory: initialized nodepme-sre, compatible id fsl,pme-sre

Using CoreNet Generic machinedescription

MMU: Supported page sizes

        4 KB as direct

      2048 KBas direct & indirect

      4096 KBas direct

     16384 KB asdirect

     65536 KB asdirect

    262144 KB as direct

   1048576 KB as direct

MMU: Book3E HW tablewalk enabled

Found initrd at0xc00000002f7fd000:0xc00000002ffff6ff

bootconsole [udbg0] enabled

CPU maps initialized for 2 threads percore

Starting Linux PPC64 #1 SMP Sun May 1501:39:21 CST 2016

-----------------------------------------------------

ppc64_pft_size   = 0x0

phys_mem_size    = 0x100000000

dcache_line_size  = 0x40

icache_line_size  = 0x40

cpu_features    =0x00180480581802c8

  possible     = 0x00180480581802c8

  always      = 0x00180400581802c0

cpu_user_features  = 0xdc008000 0x08000000

mmu_features    =0x000a0010

firmware_features  = 0x0000000000000000

-----------------------------------------------------

 <- setup_system()

Linux version 4.1.8-rt8+gbd51baf(jenkins@mercury) (gcc version 4.9.2 (GCC) ) #1 SMP Sun May 15 01:39:21 CST2016

CoreNet Generic board

Zone ranges:

  DMA     [mem 0x0000000000000000-0x000000007fffffff]

  DMA32    empty

  Normal   [mem0x0000000080000000-0x00000000ffffffff]

Movable zone start for each node

Early memory node ranges

  node   0: [mem0x0000000000000000-0x00000000ffffffff]

Initmem setup node 0 [mem0x0000000000000000-0x00000000ffffffff]

MMU: Allocated 2112 bytes of contextmaps for 255 contexts

PERCPU: Embedded 17 pages/cpu@c0000000ffe00000 s28824 r0 d40808 u131072

Built 1 zonelists in Zone order,mobility grouping on.  Total pages: 1034240

Kernel command line: root=/dev/ram rwconsole=ttyS0,115200

log_buf_len individual max cpucontribution: 4096 bytes

log_buf_len total cpu_extra contributions:28672 bytes

log_buf_len min size: 16384 bytes

log_buf_len: 65536 bytes

early log buf free: 12040(73%)

PID hash table entries: 4096 (order: 3,32768 bytes)

Dentry cache hash table entries: 524288(order: 10, 4194304 bytes)

Inode-cache hash table entries: 262144(order: 9, 2097152 bytes)

Sorting __ex_table...

Memory: 3957696K/4194304K available(7856K kernel code, 1136K rwdata, 2972K rodata, 364K init, 764K bss, 236608Kreserved, 0K cma-reserved)

Hierarchical RCU implementation.

       RCU debugfs-based tracing is enabled.

       CONFIG_RCU_FANOUT set to non-default value of 32

       Additional per-CPU info printed with stalls.

       RCU restricting CPUs from NR_CPUS=24 to nr_cpu_ids=8.

RCU: Adjusting geometry forrcu_fanout_leaf=16, nr_cpu_ids=8

NR_IRQS:512 nr_irqs:512 16

mpic: Setting up MPIC "OpenPIC  " version 1.2 at ffe040000, max 8 CPUs

mpic: ISU size: 512, shift: 9, mask: 1ff

mpic: Initializing for 512 sources

clocksource timebase: mask:0xffffffffffffffff max_cycles: 0x8a5d528ca, max_idle_ns: 440795203517 ns

clocksource: timebase mult[1aab5972]shift[24] registered

Console: colour dummy device 80x25

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 8192(order: 4, 65536 bytes)

Mountpoint-cache hash table entries:8192 (order: 4, 65536 bytes)

e6500 family performance monitorhardware support registered

Brought up 8 CPUs

devtmpfs: initialized

clocksource jiffies: mask: 0xffffffffmax_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns

xor: measuring software checksum speed

  8regs     :  3570.000 MB/sec

   8regs_prefetch: 3158.000 MB/sec

   32regs   :  3012.000 MB/sec

   32regs_prefetch: 2659.000 MB/sec

   altivec   : 5679.000 MB/sec

xor: using function: altivec (5679.000MB/sec)

NET: Registered protocol family 16

Bman ver:0a02,02,01

qman-fqd addr 0xff000000 size 0x800000

qman-pfdr addr 0xfc000000 size 0x2000000

Qman ver:0a01,03,01,02

Can't find hose for PCI bus 0!

EDAC PCI0: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe240000.pcie (INTERRUPT)

MPC85xx_edac acquired irq 20 for PCI Err

MPC85xx_edac PCI err registered

platform ffe240000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range

Found FSL PCI host bridge at0x0000000ffe250000. Firmware bus number: 0->1

PCI host bridge /pcie@ffe250000 ranges:

 MEM0x0000000c20000000..0x0000000c2fffffff -> 0x00000000e0000000

  IO0x0000000ff8010000..0x0000000ff801ffff -> 0x0000000000000000

/pcie@ffe250000: PCICSRBAR @ 0xff000007

setup_pci_atmu: end of DRAM 100000000

/pcie@ffe250000: Setup 64-bit PCI DMAwindow

/pcie@ffe250000: WARNING: Outboundwindow cfg leaves gaps in memory map. Adjusting the memory map could reduceunnecessary bounce buffering.

/pcie@ffe250000: DMA window size is0xe0000000

EDAC PCI1: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe250000.pcie (INTERRUPT)

MPC85xx_edac acquired irq 21 for PCI Err

MPC85xx_edac PCI err registered

platform ffe250000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range

Found FSL PCI host bridge at0x0000000ffe270000. Firmware bus number: 0->0

PCI host bridge /pcie@ffe270000 ranges:

 MEM0x0000000c40000000..0x0000000c4fffffff -> 0x00000000e0000000

  IO0x0000000ff8030000..0x0000000ff803ffff -> 0x0000000000000000

/pcie@ffe270000: PCICSRBAR @ 0xff000007

setup_pci_atmu: end of DRAM 100000000

/pcie@ffe270000: Setup 64-bit PCI DMAwindow

/pcie@ffe270000: WARNING: Outboundwindow cfg leaves gaps in memory map. Adjusting the memory map could reduceunnecessary bounce buffering.

/pcie@ffe270000: DMA window size is0xe0000000

EDAC PCI2: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe270000.pcie (INTERRUPT)

MPC85xx_edac acquired irq 23 for PCI Err

MPC85xx_edac PCI err registered

platform ffe270000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range

software IO TLB [mem0xf2e00000-0xf6e00000] (64MB) mapped at [c0000000f2e00000-c0000000f6dfffff]

PCI: Probing PCI hardware

fsl-pci ffe250000.pcie: PCI host bridgeto bus 0001:00

pci_bus 0001:00: root bus resource[io  0x10000-0x1ffff] (bus address [0x0000-0xffff])

pci_bus 0001:00: root bus resource [mem0xc20000000-0xc2fffffff] (bus address [0xe0000000-0xefffffff])

pci_bus 0001:00: root bus resource [bus00-01]

pci 0001:00:00.0: [Firmware Bug]: reg0x10: invalid BAR (can't size)

pci 0001:00:00.0: PCI bridge to [bus01-ff]

fsl-pci ffe270000.pcie: PCI host bridgeto bus 0002:00

pci_bus 0002:00: root bus resource[io  0x21000-0x30fff] (bus address [0x0000-0xffff])

pci_bus 0002:00: root bus resource [mem0xc40000000-0xc4fffffff] (bus address [0xe0000000-0xefffffff])

pci_bus 0002:00: root bus resource [bus00]

pci 0002:00:00.0: [Firmware Bug]: reg0x10: invalid BAR (can't size)

pci 0002:00:00.0: bridge configurationinvalid ([bus 00-00]), reconfiguring

pci 0002:00:00.0: PCI bridge to [bus01-ff]

PCI: Cannot allocate resource region 6of device 0001:00:00.0, will remap

pci 0001:00:00.0: BAR 6: no space for[mem size 0x01000000 pref]

pci 0001:00:00.0: BAR 6: failed toassign [mem size 0x01000000 pref]

pci 0001:00:00.0: PCI bridge to [bus 01]

pci 0001:00:00.0:   bridgewindow [io  0x10000-0x1ffff]

pci 0001:00:00.0:   bridgewindow [mem 0xc20000000-0xc2fffffff]

pci 0002:00:00.0: BAR 6: no space for[mem size 0x01000000 pref]

pci 0002:00:00.0: BAR 6: failed toassign [mem size 0x01000000 pref]

pci 0002:00:00.0: PCI bridge to [bus 01]

pci 0002:00:00.0:   bridgewindow [io  0x21000-0x30fff]

pci 0002:00:00.0:   bridgewindow [mem 0xc40000000-0xc4fffffff]

raid6: altivecx1 gen()  1111 MB/s

raid6: altivecx2 gen()  1850 MB/s

raid6: altivecx4 gen()  3049 MB/s

raid6: altivecx8 gen()  2969 MB/s

raid6: int64x1  gen()  519 MB/s

raid6: int64x1  xor()  775 MB/s

raid6: int64x2  gen()  873 MB/s

raid6: int64x2  xor()  927 MB/s

raid6: int64x4  gen()  1335MB/s

raid6: int64x4  xor()  1024MB/s

raid6: int64x8  gen()  1148MB/s

raid6: int64x8  xor()  831 MB/s

raid6: using algorithm altivecx4 gen()3049 MB/s

raid6: using intx1 recovery algorithm

vgaarb: loaded

SCSI subsystem initialized

usbcore: registered new interface driverusbfs

usbcore: registered new interface driverhub

usbcore: registered new device driverusb

pps_core: LinuxPPS API ver. 1 registered

pps_core: Software ver. 5.3.6 -Copyright 2005-2007 Rodolfo Giometti <[email protected]>

PTP clock support registered

EDAC MC: Ver: 3.0.0

bman-fbpr addr 0xfe000000 size 0x1000000

Bman err interrupt handler present

Bman portal initialised, cpu 0

Bman portal initialised, cpu 1

Bman portal initialised, cpu 2

Bman portal initialised, cpu 3

Bman portal initialised, cpu 4

Bman portal initialised, cpu 5

Bman portal initialised, cpu 6

Bman portal initialised, cpu 7

Bman portals initialised

Qman err interrupt handler present

QMan: Allocated lookup table at8000000000002000, entry count 131073

Qman portal initialised, cpu 0

Qman portal initialised, cpu 1

Qman portal initialised, cpu 2

Qman portal initialised, cpu 3

Qman portal initialised, cpu 4

Qman portal initialised, cpu 5

Qman portal initialised, cpu 6

Qman portal initialised, cpu 7

Qman portals initialised

Bman: BPID allocator includes range32:32

Qman: FQID allocator includes range256:512

Qman: FQID allocator includes range32768:32768

Qman: CGRID allocator includes range0:256

Qman: pool channel allocator includesrange 1025:15

No USDPAA memory, no 'fsl,usdpaa-mem' indevice-tree

fsl-ifc ffe124000.localbus: FreescaleIntegrated Flash Controller

fsl-ifc ffe124000.localbus: IFC version1.3, 8 banks

Switched to clocksource timebase

NET: Registered protocol family 2

TCP established hash table entries:32768 (order: 6, 262144 bytes)

TCP bind hash table entries: 32768(order: 7, 524288 bytes)

TCP: Hash tables configured (established32768 bind 32768)

UDP hash table entries: 2048 (order: 4,65536 bytes)

UDP-Lite hash table entries: 2048(order: 4, 65536 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX sockettransport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchanneltransport module.

Trying to unpack rootfs image asinitramfs...

rootfs image is not initramfs (no cpiomagic); looks like an initrd

Freeing initrd memory: 8200K (c00000002f7fd000- c00000002ffff000)

futex hash table entries: 2048 (order:5, 131072 bytes)

audit: initializing netlink subsys(disabled)

audit: type=2000 audit(1.756:1):initialized

HugeTLB registered 4 MB page size,pre-allocated 0 pages

HugeTLB registered 16 MB page size,pre-allocated 0 pages

HugeTLB registered 64 MB page size,pre-allocated 0 pages

HugeTLB registered 256 MB page size,pre-allocated 0 pages

HugeTLB registered 1 GB page size,pre-allocated 0 pages

NFS: Registering the id_resolver keytype

Key type id_resolver registered

Key type id_legacy registered

ntfs: driver 2.1.32 [Flags: R/O].

jffs2: version 2.2. (NAND) 2001-2006Red Hat, Inc.

async_tx: api initialized (async)

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 4 ports, IRQsharing enabled

console [ttyS0] disabled

serial8250.0: ttyS0 at MMIO 0xffe11c500(irq = 36, base_baud = 18748125) is a 16550A

console [ttyS0] enabled

console [ttyS0] enabled

bootconsole [udbg0] disabled

bootconsole [udbg0] disabled

serial8250.0: ttyS1 at MMIO 0xffe11c600(irq = 36, base_baud = 18748125) is a 16550A

serial8250.0: ttyS2 at MMIO 0xffe11d500(irq = 37, base_baud = 18748125) is a 16550A

serial8250.0: ttyS3 at MMIO 0xffe11d600(irq = 37, base_baud = 18748125) is a 16550A

ePAPR hypervisor byte channel driver

brd: module loaded

loop: module loaded

st: Version 20101219, fixed bufsize32768, s/g segs 256

fsl-sata ffe220000.sata: Sata FSLPlatform/CSB Driver init

scsi host0: sata_fsl

ata1: SATA max UDMA/133 irq 68

fsl-sata ffe221000.sata: Sata FSLPlatform/CSB Driver init

scsi host1: sata_fsl

ata2: SATA max UDMA/133 irq 69

fe8000000.nor: Found 1 x16 devices at0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00227e

Amd/Fujitsu Extended Query Table at0x0040

  Amd/Fujitsu Extended Queryversion 1.3.

number of CFI chips: 1

nand: device found, Manufacturer ID:0x2c, Chip ID: 0xac

nand: Micron MT29F4G08ABBDAH4

nand: 512 MiB, SLC, erase size: 128 KiB,page size: 2048, OOB size: 64

Bad block table found at page 262080,version 0x01

Bad block table found at page 262016,version 0x01

fsl,ifc-nand fff800000.nand: IFC NANDdevice at 0xfff800000, bank 1

fsl_espi ffe110000.spi: cs=0,init_csmode=0x100008

m25p80 spi32766.0: found n25q512ax3,expected n25q512a

m25p80 spi32766.0: n25q512ax3 (65536Kbytes)

fsl_espi ffe110000.spi: at0x80000800809ae000 (irq = 53)

libphy: Fixed MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

libphy: Freescale XGMAC MDIO Bus: probed

cpu0/24: > WARNING (FM) [CPU00,/home/jenkins/ci/sdk/master/t2080rdb/sources/linux/drivers/net/ethernet/freescale/sdk_fman/Peripherals/FM/fm.c:3547FM_Init]:

cpu0/24: Hack: No FM reset!

cpu0/24:

Freescale FM module, FMD API version21.1.0

Freescale FM Ports module

fsl_mac: fsl_mac: FSL FMan MAC API baseddriver

fsl_mac ffe4e0000.ethernet: FMan MEMAC

fsl_mac ffe4e0000.ethernet: FMan MACaddress: 00:04:9f:04:74:2e

fsl_mac ffe4e2000.ethernet: FMan MEMAC

fsl_mac ffe4e2000.ethernet: FMan MACaddress: 00:04:9f:04:74:2f

fsl_mac ffe4e4000.ethernet: FMan MEMAC

fsl_mac ffe4e4000.ethernet: FMan MACaddress: 00:04:9f:04:74:30

fsl_mac ffe4e6000.ethernet: FMan MEMAC

fsl_mac ffe4e6000.ethernet: FMan MACaddress: 00:04:9f:04:74:31

fsl_mac ffe4f0000.ethernet: FMan MEMAC

fsl_mac ffe4f0000.ethernet: FMan MACaddress: 00:04:9f:04:74:32

fsl_mac ffe4f2000.ethernet: FMan MEMAC

fsl_mac ffe4f2000.ethernet: FMan MACaddress: 00:04:9f:04:74:33

fsl_dpa: FSL DPAA Ethernet driver

fsl_dpa: fsl_dpa: Probed interface eth0

fsl_dpa: fsl_dpa: Probed interface eth1

fsl_dpa: fsl_dpa: Probed interface eth2

fsl_dpa: fsl_dpa: Probed interface eth3

fsl_dpa: fsl_dpa: Probed interface eth4

fsl_dpa: fsl_dpa: Probed interface eth5

fsl_advanced: FSL DPAA Advanced drivers:

fsl_proxy: FSL DPAA Proxy initializationdriver

fsl_dpa_shared: FSL DPAA Shared Ethernetdriver

fsl_dpa_macless: FSL DPAA MAClessEthernet driver

fsl_oh: FSL FMan Offline Parsing portdriver

e1000e: Intel(R) PRO/1000 Network Driver- 2.3.2-k

e1000e: Copyright(c) 1999 - 2014 IntelCorporation.

fsl-of-dma ffe100300.dma: dma channeldma-uio0-0 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-1 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-2 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-3 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-4 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-5 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-6 initialized

fsl-of-dma ffe100300.dma: dma channeldma-uio0-7 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-0 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-1 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-2 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-3 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-4 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-5 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-6 initialized

fsl-of-dma ffe101300.dma: dma channeldma-uio1-7 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-0 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-1 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-2 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-3 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-4 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-5 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-6 initialized

fsl-of-dma ffe102300.dma: dma channeldma-uio2-7 initialized

ehci_hcd: USB 2.0 'Enhanced' HostController (EHCI) Driver

ehci-pci: EHCI PCI platform driver

fsl-ehci fsl-ehci.0: Freescale On-ChipEHCI Host Controller

fsl-ehci fsl-ehci.0: new USB busregistered, assigned bus number 1

fsl-ehci fsl-ehci.0: irq 44, io mem0xffe210000

fsl-ehci fsl-ehci.0: USB 2.0 started,EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

fsl-ehci fsl-ehci.1: Freescale On-ChipEHCI Host Controller

fsl-ehci fsl-ehci.1: new USB busregistered, assigned bus number 2

ata1: No Device OR PHYRDY change,Hstatus= 0xa0000000

ata1: SATA link down (SStatus 10SControl 300)

fsl-ehci fsl-ehci.1: irq 45, io mem0xffe211000

ata2: No Device OR PHYRDY change,Hstatus= 0xa0000000

ata2: SATA link down (SStatus 10SControl 300)

fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 1 port detected

usbcore: registered new interface driverusb-storage

i2c /dev entries driver

mpc-i2c ffe118000.i2c: timeout 1000000us

rtc-ds1307 0-0068: rtc core: registeredds1339 as rtc0

mpc-i2c ffe118100.i2c: timeout 1000000us

mpc-i2c ffe119000.i2c: timeout 1000000us

mpc-i2c ffe119100.i2c: timeout 1000000us

i2c i2c-1: Added multiplexed i2c bus 4

i2c i2c-1: Added multiplexed i2c bus 5

i2c i2c-1: Added multiplexed i2c bus 6

i2c i2c-1: Added multiplexed i2c bus 7

pca954x 1-0077: registered 4 multiplexedbusses for I2C switch pca9546

md: raid6 personality registered forlevel 6

md: raid5 personality registered forlevel 5

md: raid4 personality registered forlevel 4

Freescale(R) MPC85xx EDAC driver, (C)2006 Montavista Software

EDAC MC0: Giving out device to moduleMPC85xx_edac controller mpc85xx_mc_err: DEV mpc85xx_mc_err (INTERRUPT)

MPC85xx_edac acquired irq 490 for MC

MPC85xx_edac MC err registered

sdhci: Secure Digital Host ControllerInterface driver

sdhci: Copyright(c) Pierre Ossman

sdhci-pltfm: SDHCI platform and OFdriver helper

sdhci-esdhc ffe114000.sdhc: No vmmcregulator found

sdhci-esdhc ffe114000.sdhc: No vqmmcregulator found

mmc0: SDHCI controller on ffe114000.sdhc[ffe114000.sdhc] using ADMA 64-bit

platform caam_qi.0: Linux CAAM Queue I/Fdriver initialised

caam ffe300000.crypto: Instantiated RNG4SH1

caam ffe300000.crypto: device ID =0x0a13020000000000 (Era 6)

caam ffe300000.crypto: job rings = 4, qi= 1

caam algorithms registered in /proc/crypto

platform caam_qi.0: fsl,sec-v5.2algorithms registered in /proc/crypto

caam_jr ffe301000.jr: registeringrng-caam

caam ffe300000.crypto: fsl,sec-v5.2algorithms registered in /proc/crypto

usbcore: registered new interface driverusbhid

usbhid: USB HID core driver

Freescale USDPAA process driver

fsl-usdpaa: no region found

Freescale USDPAA process IRQ driver

dce_sys_init done!

fsl-dce ffe312000.dce: Device/soc@ffe000000/dce@312000 initialized ver: 0x0af00101

fsl-pme ffe316000.pme: ver: 0x00100201

Freescale pme2 db driver

Freescale pme2 scan driver

fsl-pme2-scan: device pme_scanregistered

Freescale hypervisor management driver

fsl-hv: no hypervisor found

ipip: IPv4 over IPv4 tunneling driver

Initializing XFRM netlink socket

NET: Registered protocol family 10

sit: IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

NET: Registered protocol family 15

8021q: 802.1Q VLAN Support v1.8

Key type dns_resolver registered

fsl_generic: FSL DPAA Generic Ethernetdriver

rtc-ds1307 0-0068: setting system clockto 2016-05-14 17:50:59 UTC (1463248259)

md: Skipping autodetection of RAIDarrays. (raid=autodetect will force)

RAMDISK: gzip image found at block 0

VFS: Mounted root (ext2 filesystem) ondevice 1:0.

devtmpfs: mounted

Freeing unused kernel memory: 364K(c000000000a9a000 - c000000000af5000)

INIT: version 2.88 booting

Starting udev

udevd[1358]: starting version 182

fsl_dpa fsl,dpaa:ethernet@0 fm1-mac1:renamed from eth0

udevd[1365]: renamed network interfaceeth0 to fm1-mac1

fsl_dpa fsl,dpaa:ethernet@1 fm1-mac2:renamed from eth1

fsl_dpa fsl,dpaa:ethernet@2 fm1-mac3:renamed from eth2

udevd[1363]: renamed network interfaceeth1 to fm1-mac2

fsl_dpa fsl,dpaa:ethernet@3 fm1-mac4:renamed from eth3

udevd[1361]: renamed network interfaceeth2 to fm1-mac3

fsl_dpa fsl,dpaa:ethernet@9 fm1-mac10:renamed from eth5

udevd[1366]: renamed network interfaceeth3 to fm1-mac4

fsl_dpa fsl,dpaa:ethernet@8 fm1-mac9:renamed from eth4

udevd[1367]: renamed network interfaceeth5 to fm1-mac10

udevd[1364]: renamed network interfaceeth4 to fm1-mac9

bootlogd: cannot allocate pseudo tty: Nosuch file or directory

random: dd urandom read with 8 bits ofentropy available

Populating dev cache

Running postinst/etc/rpm-postinsts/100-sysvinit-inittab...

update-rc.d: /etc/init.d/run-postinstsexists during rc.d purge (continuing)

INIT: Entering runlevel: 5

Configuring network interfaces... done.

Starting OpenBSD Secure Shell server:sshd

  generating ssh RSA key...

  generating ssh ECDSA key...

  generating ssh DSA key...

  generating ssh ED25519 key...

done.

Starting syslogd/klogd: done

QorIQ SDK (FSL Reference Distro) 2.0t2080rdb /dev/ttyS0

t2080rdb login: root

t2080rdb~

 


版权声明:本文为博主原创文章,遵循 CC 4.0 BY-SA 版权协议,转载请附上原文出处链接和本声明。
本文链接:https://blog.csdn.net/cph77777/article/details/79555981

智能推荐

【Linux :编辑文件的方式】_linux 非交互方式修改文件-程序员宅基地

文章浏览阅读815次。一般可以把文件用sftp方式下载下来,在本地电脑修改好后再上传上去, 但有时候可能必须在linux里面修改,在Linux里面修改涉及到两种方式第一种:vi/vim两个常用linux端文本编辑工具, vi/vim 编辑工具1.vi/vim是什么?①vi是Visual Interface的缩写,即 可视化接口②vim是vi iMprove的缩写,即 vi的增强版(具有语法着色功能)2.vim模式有哪些?如何切换?①三种模式命令模式(默认):刚进入vim的时候,默认就是 命令模式,可以复制行,删除_linux 非交互方式修改文件

Imagination先进半导体IP引领汽车智能化发展 | IC China2020-程序员宅基地

文章浏览阅读155次。10月14-16日,由中国半导体行业协会、中国电子信息产业发展研究院主办的第三届全球IC企业家大会暨第十八届中国国际半导体博览会(IC China 2020)在上海新举行。本届大会暨博览..._imagination的半导体接口ip

Linux基础入门_linux license agreement-程序员宅基地

文章浏览阅读251次。Linux基础入门及安装虚拟机、操作系统_linux license agreement

uniapp - 实现日期选择器(年月日)组件,兼容 H5、App、小程序,提供组件源码可直接复制运行!_uni-app封装日期时间选择器-程序员宅基地

文章浏览阅读4.8k次,点赞3次,收藏3次。uniapp日期选择器,uniapp兼容h5小程序app的年月日选择器功能组件,uniapp日期选择组件插件源码,uniapp日期选择弹框示例代码,uniapp年月日的日期选择器组件,uniapp日期选择器(年月日),Uniapp实现了日期选择器,uniapp实现日期选择效果,uni-app 自定义选择日期,uniapp实现日期的选择,uni-app中组件picker的日期选择器,uniapp里怎么做日期选择功能,uniapp如何实现选择日期的弹框,uniapp不引组件库怎么实现日期选择,uniapp日期组_uni-app封装日期时间选择器

ACE2005语料库文件格式及内容解析_ace05-程序员宅基地

文章浏览阅读1.6k次。前提ACE2005语料库是语言数据联盟(LDC)发布的由实体,关系和事件注释组成的各种类型的数据,包括英语,阿拉伯语和中文培训数据,目标是开发自动内容提取技术,支持以文本形式自动处理人类语言。ACE语料解决了五个子任务的识别:entities、values、temporal expressions、relations and events。这些任务要求系统处理文档中的语言数据,然后为每个文档输出有关其中提到或讨论的实体,值,时间表达式,关系和事件的信息。ACE语料库的获取链接:https://cata_ace05

yolov3训练自己的数据_windows yolov3训练自己的数据-程序员宅基地

文章浏览阅读878次,点赞3次,收藏4次。谈谈如何实现用yolov3训练自己的数据前言:早就听说yolov3算法识别率高,“快如闪电,可称目标检测之光”,最近在研究yolov3算法,动手训练了自己的数据集,其间出现很多问题,所以写下这篇博客记录一下。一.编译源码并运行demo运行demo的话,我主要是采用YunYang1994的代码,github上的代码链接为:https://github.com/YunYang1994/tens..._windows yolov3训练自己的数据

随便推点

如何使用promise封装 原生ajax,$.ajax(),以及fetch?(使用promise封装之后,使用封装好的方法请求接口,三种方法都可以好使)_new promise如何套用原生ajax-程序员宅基地

文章浏览阅读203次。文章目录1.如何使用promise封装原生ajax2.如何使用promise封装$ajax()3.fetch的使用1.fetch请求数据2.Response对象1.如何使用promise封装原生ajaxget function getRequest(url) { return new Promise((resolve, reject) => { const xhr = new XMLHttpRequest() xhr.open(_new promise如何套用原生ajax

聊聊通用的架构设计_thoughtwork 技术全景-程序员宅基地

文章浏览阅读8.6k次,点赞2次,收藏12次。本文通过从业务架构到IT架构,以及IT架构下的应用架构、数据架构、技术架构和基础设施架构的介绍,配合一些示例的展示,描绘了架构设计中一般包含哪些内容。_thoughtwork 技术全景

你了解这些常用器件封装及其名字来历么?-程序员宅基地

文章浏览阅读1.7k次,点赞2次,收藏30次。关注、星标公众号,不错过精彩内容1、BGA|ball grid array也称CPAC(globe top pad array carrier)。球形触点陈列,表面贴装型封装之一。在印刷基板的背面按陈列方式制作出球形凸点用以代替引脚,在印刷基板的正面装配LSI 芯片,然后用模压树脂或灌封方法进行密封。也称为凸点陈列载体(PAC)。引脚可超过200,是多引脚LSI用的一种封装。封装本体也可做得比QF..._弹针封装的命名

IDEA 当前项目jdk版本查看_idea查看项目jdk版本-程序员宅基地

文章浏览阅读8.2k次,点赞3次,收藏2次。File->Project Structure->project->SDKmaven打包JDKFile->Settings->runner->jreFile->Settings->Importing->jdk_idea查看项目jdk版本

Chrome等浏览器下出现net::ERR_BLOCKED_BY_CLIENT的解决办法-程序员宅基地

文章浏览阅读1.1w次,点赞4次,收藏2次。1.在开发过程中,打开网页的调试检查页面,有时候我们会看到 net::ERR_BLOCKED_BY_CLIENT这样的错误。2.这种情况是因为我们在浏览器扩展中安装了广告过滤插件,关闭广告过滤插件即可。3.关闭后结果..._net::err_blocked_by_client

ubuntu20.04——hdaudioC0D2: unable to bind the codec-程序员宅基地

文章浏览阅读1.1w次,点赞3次,收藏48次。问题不久前尝试双系统,win10+ubuntu20.04,安装比较顺利,能够正常进入系统。但是,当我更新了显卡驱动后(专有 nvidia-drivers-390),重启就无法进入系统的图形界面,一直卡在下面这个页面。如下图:解决之后,选择ubunru 高级选项,选择低版本的内核启动,却可以进入图形界面。但是,这样让我很不爽。。。最后,我找到某位大佬说进入/etc/default/grub编辑:可以使用低版本的内核启动图形界面进入编辑,也可以 Ctr+Alt+F2 进入命令行编辑;# 原_unable to bind the codec